2021-2022 Atomic Backland Carbon

Boot: 2021-2022 Atomic Backland Carbon

Stated Flex: 110

Available Sizes: 24-30.5

Stated Last (size 26.5): 98 mm (heat moldable)

Stated Range of Motion: 74°

Stated Forward Lean: 15° (adjustable to 13° and 17°)

Size Tested: 27.5

Stated Boot Sole Length (size 27.5): 298 mm

Blister’s Measured Weight (size 27.5):

  • Shells, no Liners: 882 & 884 g
  • Liners, no Footbeds: 228 & 230 g
  • Shells + Liners = 1110 & 1114 g

Buckles: 1 micro-adjustable upper buckle + BOA closure

Powerstrap: 40 mm cam-style

Shell Material:

  • Cuff: Carbon Fiber
  • Shoe / Clog: “Carbon-Loaded Polyamide”

Soles: full-rubber, rockered, fixed

Binding Compatibility: tech bindings w/ pin toes and pin heels

Tech Fittings: yes

Test Location: Chugach Mountains, AK

Days Tested: ~7

[Note: Our review was conducted on the 19/20 Backland Carbon, which returns unchanged for 20/21 and 21/22, apart from graphics.]

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
Atomic Backland Carbon
Review Navigation:  Specs //  Intro //  Weight & Comparisons //  Design & Features //  Fit //  Uphill Performance //  Downhill Performance //  Bottom Line

Intro

For the 19/20 season, Atomic overhauled their line of lightweight touring boots — the Backland series.

Serving as the more uphill-oriented complement to their hard-charging Hawx Ultra XTD series, the Backland boots slot into the class of very light touring boots with excellent uphill mobility, while reportedly still delivering enough stiffness and power to ski relatively hard in the backcountry.

I reviewed the previous Backland Carbon and came away quite impressed. But while that boot compared favorably to its competitors, it was a bit finicky with its removable tongues and I ended up making a lot of modifications to try to make it ski better (as I have done with many boots in this class). Well, Atomic seems like they’ve been listening to what people have been saying, and the updates to the new boot have us very excited.

I’ve now used the new Backland Carbon for many days in the Alaskan backcountry and you can check out my full review below, but first, let’s take a closer look at the new design.

2019-2020 Atomic Backland Boot Lineup

The 19/20 Backland boot line consists of 7 boots. At the most uphill-oriented end of the spectrum is the Backland Ultimate, which Atomic markets as an “endurance touring boot” and some would call a skimo race boot, and that features a lower cuff (vs. the other Backland boots), ultralight Grilamid & carbon shell / cuff, and walk mechanism that’s integrated into the cuff closure for quicker transitions. At the most downhill-oriented end of the spectrum is the boot we’re reviewing, the Backland Carbon, which features a carbon-fiber cuff, carbon-reinforced shoe / clog, and a stated flex of 110.

For reference, here’s a quick breakdown of the whole 19/20 Atomic Backland boot line. And if any of the talk about different plastics and constructions is confusing, we highly recommend listening to our GEAR:30 podcast with Atomic Ski Boots product manager, Matt Manser.

Backland Ultimate

  • Stated Weight (size 26.5): 750 g
  • Stated Flex: 70
  • Shell / Cuff Material: Grilamid & carbon-loaded Grilamid / carbon fiber

Backland Expert W

  • Stated Weight (size 26.5): 1160 g
  • Stated Flex: 85
  • Shell / Cuff Material: True Flex PU / True Flex PU

Backland Sport

  • Stated Weight (size 26.5): 1206 g
  • Stated Flex: 90
  • Shell / Cuff Material: True Flex PU / True Flex PU
  • Note: this budget-oriented boot retains the removable-tongue and non-BOA design of the previous Backland boots.

Backland Expert

  • Stated Weight (size 26.5): 1173 g
  • Stated Flex: 90
  • Shell / Cuff Material: True Flex PU / True Flex PU

Backland Pro W

  • Stated Weight (size 26.5): 1097 g
  • Stated Flex: 95
  • Shell / Cuff Material: polyamide / polyamide

Backland Pro

  • Stated Weight (size 26.5): 1102 g
  • Stated Flex: 100
  • Shell / Cuff Material: polyamide / polyamide

Backland Carbon

  • Stated Weight (size 26.5): 1094 g
  • Stated Flex: 110
  • Shell / Cuff Material: carbon-loaded polyamide / carbon fiber

Weight + Comparisons

The new Backland Carbon is a bit lighter than the old version, and it still slots right around the middle of the “lightweight touring boot” category in terms of weight; not as light as the very minimal Scarpa Alien RS, but not as heavy as the Salomon S/Lab X-Alp. And even compared to some of the lightest “freeride touring boots” like the Tecnica Zero G Tour Pro and Atomic Hawx Ultra XTD 130, the Backland Carbon is significantly lighter.

For reference, here are some of our measured weights for several boots in this class, and then two boots in the heavier, more downhill-oriented touring category. Keep in mind the size differences to try to keep things apples-to-apples.

988 & 991 Scarpa Alien RS, 28.0 (18/19–19/20)
1014 & 1023 Dynafit TLT Speedfit, 26.5 (18/19–19/20)
1064 & 1070 Fischer Travers Carbon, 27.5 (16/17–18/19)
1065 & 1069 Dynafit TLT 7 Performance, 28.5 (17/18–18/19)
1110 & 1114 Atomic Backland Carbon, 27.5 (19/20)
1167 & 1170 Atomic Backland Carbon, 27.5 (15/16–18/19)
1232 & 1232 Salomon S/Lab X-Alp, 27.5 (17/18–19/20)
1288 & 1286 Arc’teryx Procline Carbon Support, 27.5 (16/17–19/20)
~1310 (avg. weight) Scarpa F1, 28.0 (17/18–19/20)
1309 & 1311 Tecnica Zero G Tour Pro, 26.5 (18/19–19/20)
1406 & 1414 Atomic Hawx Ultra XTD 130, 26.5 (19/20)

Heat-Moldable Shell

Apart from the Backland Sport, all of the new Backland boots still feature Atomic’s “Memory Fit” heat-moldable shells. Heat-moldable shells are fairly rare in the lightweight touring category, and this is something that sets apart the Backland boots from much of their competition.

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
Atomic Backland Carbon

One notable update to the shells of the new Backland boots is that their cuff height has increased slightly, which is a plus since the old Backland boots’ low cuffs didn’t do a great job of transferring power evenly across your shins, particularly for larger skiers. This was a big reason why I decided to modify my Backland Carbons and swap the stock liner for a much taller Intuition Power Wrap liner. That said, the new Backland Carbon is still a bit shorter than most “freeride touring boots” like the Atomic Hawx Ultra XTD.

Liner

The liner in the Backland Carbon is pretty standard fare for a boot in this class. Its liner is quite thin, very pliable, and much less substantial compared to the liners in heavier touring boots. It has the standard “flex zone” near the Achilles area, minimal reinforcements around the back of the calf and the tongue area, and is fully heat-moldable.

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
19/20 Atomic Backland Carbon — Liner

To align with the slightly higher cuff height of the shell, the liner in the new Backland Carbon is also a bit taller than the previous version’s liner.

The Backland Carbon’s liner is also fully machine-washable, and it has a perforated sole that’s meant to increase breathability.

Walk Mechanism & Range of Motion

The new Backland boots’ “Free/Lock 4.0” walk mechanism is nearly identical to the previous versions. It’s still fully external, comprised mostly of a big chunk of aluminum, and seems bomber, based on our experience with the old Backland Carbon and Atomic Hawx Ultra XTD boots, which use a walk mechanism that’s essentially the same. According to Atomic, the difference between the Free/Lock 4.0 mechanism on the 19/20 Backland boots and the previous Free/Lock 2.0 system is the ability to change the forward lean on the 4.0 version without removing the walk mechanism and using a flip chip like the previous version. Instead of using a flip chip, you simply loosen two bolts with an Allen key and slide the walk mechanism up or down to adjust the forward lean. The Backland Carbon comes standard in the 15° forward lean setting, and you can adjust it to 13° or 17°.

The large bar on the back of the Backland boots has a hook that locks into a bar on the lower cuff of the boot, locking the cuff for ski mode and freeing up a claimed 74° range of motion in walk mode. It also has a small plastic / cord tab on the end to make it easy to grab.

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
19/20 Atomic Backland Carbon — walk mechanism in ski mode (left) and walk mode (right)

One key difference between the Backland Carbon and one of its most notable competitors, the Dynafit TLT8 Carbonio, is that the Backland Carbon’s walk mechanism is not integrated into any of its buckles. Dynafit’s “Ultra Lock” walk mechanism not only engages its cuff when in ski mode, but at the same time tightens down its upper buckle (and vice versa in walk mode). That system makes for even quicker transitions, though in past Ultra Lock Dynafit boots, we’ve had experiences with the walk mechanism disengaging during high-impact scenarios. So as always, there are tradeoffs to be made. With the Backland boots, Atomic seems to be opting to lose a bit of efficiency during transitions in exchange for a potentially stronger / more reliable ski mode. We’ll see how that pans out on snow.

Buckles (or Lack Thereof)

As you probably noticed as soon as you looked at the new Backland boots, this is one of the other areas where the boots saw significant change. Instead of the buckle / cable system on the old Backland boots, the new versions have a single BOA dial closure. The BOA system is designed to accomplish the same goal as a traditional buckle (securing your instep and forefoot) but does so with a single dial adjustment and cable system that’s hidden underneath the Backland’s textile gaiter. Atomic says the switch to the BOA system was meant to make it easier to transition and make it more durable since the BOA dial over the instep is reportedly less prone to damage while scrambling (vs. the buckle on the side of the old boot).

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
19/20 Atomic Backland Carbon

The new Backland boots’ gaiter covers the instep and forefoot area and extends about halfway up the cuff to help keep out water and snow. It has magnetic tabs that are designed to connect it to the liner. Taking the liners in and out of the boot, that gaiter tends to get in the way (a slight annoyance with the old version, too). Though while messing with the boot indoors, the gaiter is barely noticeable once the liner is in the boot since its secured under the cuff of the boot. We’re curious to see if that gaiter presents any issues in the backcountry.

What’s really interesting here is the decision to ditch the old Backland’s removable tongue. That tongue was where the old boot got most of its stiffness in ski mode, but Atomic is claiming that the 19/20 Backland Carbon still has the same 110 flex as the old version. Like the Scarpa Alien RS, the new Backland Carbon’s stiffness in ski mode will come from the connection and rigidity of its cuff and lower shell, rather than a tongue. Atomic’s Matt Manser said that the new Backland Carbon’s max stiffness is identical to the Atomic Hawx Prime 110, but they aimed for a more progressive flex pattern with the new Backland Carbon (i.e., softer initially, but with a smooth ramp-up). The old Backland Carbon did not have a very progressive flex pattern, so this could be a big improvement. And just while flexing the boot indoors, the flex does feel quite progressive for a boot in this class.

Up top, the Backland Carbon has a single buckle that’s similar to the Atomic Hawx Ultra XTD boots, in that it has a slider that lets you significantly loosen the buckle, even when it’s still attached to the hooks on the boot’s cuff.

These buckles can make for quicker transitions since you can flip the buckle open and get good range of motion without fully removing it from the hooks on the cuff, and therefore just need to close the buckle and tighten the power strap to secure it in ski mode. To keep the buckle on the hooks, even when the buckle is disengaged, there is a small metal latch (the silver bar shown above) that covers the buckle-latch / hook interface.

Power Strap

Another update: the new Backland Carbon now has a wider, 40 mm power strap, and this one has a cam-style ratchet, rather than the narrower, velcro-style power strap on the old version. Many of us have become fans of cam-style power straps on other boots, and the wider power strap on the new Backland Carbon seems like a sensible update, given how insubstantial the power strap was on the old version.

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
19/20 Atomic Backland Carbon — Power Strap & Upper Buckle

Like the power strap on the 19/20 Atomic Hawx Ultra XTD 130, the material on the 19/20 Backland Carbon’s power strap is extremely thin, but its wider shape should still help it more effectively and evenly distribute pressure than the thinner strap on the old version.

Soles & Binding Compatibility

Not much change here — the 19/20 Backland Carbon still has a rockered, fixed, full-rubber sole. The tread looks basically identical to the old version’s sole.

The 19/20 size 27.5 Backland Carbon has the same stated BSL (298 mm) as the old size 27.5 Backland Carbon. Like most boots in this category, the Backland Carbon’s BSL is shorter than more downhill-oriented boots of the same size, which is in part due to the Backland Carbon’s very short toe welt. This is meant to move the pivot point closer to your toes when skinning in tech bindings for a more efficient stride, and it also often equates to a more comfortable and natural walking experience when you’re off your skis.

Blister reviews the 2019-2020 Atomic Backland Carbon Ski Boot
19/20 Atomic Backland Carbon — Sole

 The Backland Boots are only compatible with traditional “tech” or “pin” bindings with pins at both the toes and heels. The Backland will not work with MNC bindings (e.g., Atomic Shift MNC, Atomic Warden MNC, etc.) or hybrid tech bindings with alpine-like heels (e.g., Marker Kingpin & Fritschi Tecton).

Fit

As always, buy your boots from a reputable bootfitter. Fit is by far the most important aspect of ski boots, and that’s where you should start. With that said, here’s my experience with the fit of the new Backland Carbon.

I’ve been told by experienced bootfitters that I have a low-volume heel and ankle, high instep, and medium-width forefoot. My most common problem area is my high instep followed by a frequent need for a 5th metatarsal or “6th toe” punch.

I struggled with the fit of the previous version of the Backland Carbon and found it to be a bit too low-volume throughout (for my feet) and often felt like I could have easily bumped up to the next size. The new 19/20 version fit we me well in my usual size (27.5) and I never had the thought that I’d need to bump up a size. The heel and ankle area are low-volume enough that I had very little movement both on the ascent and descent, but I think those with higher-volume ankles will probably still be okay with some heat molding. The forefoot similarly proved ample for my foot and I haven’t felt the need for a punch or molding in that area. The new Backland Carbon’s instep works pretty well for my high-instep foot since the BOA allows me to expand the fit in the upward direction. I have been able to find a comfortable-but-snug position, but I could see how those with a very low instep or very low-volume foot might struggle here. The BOA on the Backland Carbon really only changes the volume / shape of the boot in an up / down direction, and in terms of how tight you can get it, the BOA kind of maxes out level / even with the sides of the lower shell. As a result, those who would want to pull the sides of the boot inward or those with a very low instep might need to look elsewhere or add some shims on the boot board to suck up some volume. [Editor’s Note: Reviewer Luke Koppa has a low instep and when he tried on the Backland Carbon, he was unable to get a very secure fit over his instep.]

It’s worth noting here that the liner on the new Backland Carbon is overall much thicker and more padded than the original 15/16 Backland Carbon’s liner. The new liner heat molds effectively and provides a nice balance of cushioning while still feeling reasonable firm and low volume in the right places for me. In the past, I have ultimately replaced many of the stock liners that come with this style of lightweight, 2-buckle touring boots but I will happily keep using the Backland Carbon’s stock liner.

Some Questions / Things We’re Curious About

(1) With no tongue, just how stiff will the new Backland Carbon be? We’ve found most of the boots in this weight class to perform very similarly on the downhill, so will the new Backland Carbon be similar, better, or worse than its competitors when headed downhill?

(2) While the old Backland Carbon was stiff for its weight, its flex pattern was not very progressive (i.e., kind of felt like hitting a “brick wall”). Without a stiff tongue, will the new Backland Carbon’s flex be more progressive and / or offer better damping and suspension when skiing through variable snow and terrain?

(3) The new Backland Carbon has the same stated range of motion as the previous version (74°), but it should be quicker to transition due to its lack of a removable tongue. But will we notice any other upsides or downsides in terms of skinning, walking, and transitions?

(3) How effective is the BOA closure in terms of securing your instep and forefoot? And will we run into any durability issues while scrambling around in the new Backland Carbon?

Bottom Line (For Now)

With the 19/20 Backland Carbon, Atomic seems to have addressed many of the qualms we had with the old boot, and we’re very excited to see how it compares to the boot it replaced — and numerous other boots in this category. Stay tuned for our full review.

Uphill Performance

In large part due to the combination of a comfortable, blister-free fit on my foot and a reasonably light total weight, the 19/20 Backland Carbon is a joy to tour in. I’ve found the range of motion (ROM) to be more than adequate for anything I did in these boots, including long approaches, the occasional short downclimb through rocky terrain, and long, steep skin tracks. The walk mode felt frictionless and the boots pretty much disappeared under me as I skied lap after lap of early season powder with a variety of skis.

Paul Forward reviews the Atomic Backland Carbon for BLISTER
Paul Forward skinning in the Atomic Backland Carbon.

For those who have never enjoyed the touring comfort of one of the high-ROM, lightweight, 2-buckle touring boots, you’re missing out. The short soles bring the pins closer to your toes, making for a more natural stride, and also make scrambling and walking around (without skis) much more comfortable. The Backland Carbon remains a great example of this. As an aside, I do a lot of driving in all kinds of ski boots (which I wouldn’t recommend to others), and driving home from Turnagain pass in the Backland Carbon is almost the same as driving home in hiking boots.

Transitions with the new Backland Carbon are easier than with the older version of the boot, primarily because Atomic has done away with the removable tongue. I have owned quite a few pairs of boots with removable tongues and never minded it too much but I’m not sad to see that go away, at least from the perspective of transitions. The lack of a tongue is also really nice for flat sections on the way back to the car where I used to just deal with leaving it in but now can quickly flip the boot into walk mode and stroll across the flats more comfortably — even without transitioning the binding to walk mode.

I’ll do some detailed comparisons in a Deep Dive comparison but for now, suffice to say that as nice as the Backland Carbon is on the up and on the transitions, it still feels a bit more finicky compared to some of the boots out there that allow you to lock the upper buckle and the walk / ski mechanism in one motion. A fairly subtle difference, but worth noting for those who’ve grown accustomed to the super quick transitions of boots with those types of buckle / walk mechanism layouts.

Warmth

Alaska has experienced some refreshingly cold temps over the last month and I’ve been out in Backland Carbon in some sub-zero Fahrenheit ( around -20°C) conditions a few times this year. I wondered if the liners, with their perforated soles, combined with the fairly thin Grilamid shell, would lead to colder feet in these conditions. I was pleasantly surprised to find that I stayed quite warm even on long (relative to our limited daylight, anyway) days of touring.

Downhill Performance

From the standpoint of pure forward-flex stiffness, the original Backland Carbon was one of the stiffest boots in that category that I’ve used. To that end, the shell and tongue were stiff enough that descending in them was uncomfortable for me in the super-thin stock liners that just didn’t have enough padding to cushion the various edges of the shell when pushing hard in the boot. I ended up replacing the liners on my pair with Intuition wrap liners and added a Booster strap (both of which further stiffened the forward flex) to gain some added comfort around the cuff.

Paul Forward reviews the Atomic Backland Carbon for BLISTER
Paul Forward skiing in the Atomic Backland Carbon.

So, how does the 19/20 Backland Carbon stack up? In short, the new Backland Carbon doesn’t quite match the max stiffness of the old version, but the new boot’s flex is more progressive and the boot, right out of the box, is far more comfortable — especially on firmer and bumpier snow. The new Backland Carbon’s flex starts pretty linear (i.e., easy to flex with little ramp-up), but as you go deeper, it ramps up nicely. There’s no hard “wall” like on the previous Backland Carbon, though it’s certainly possible for a bigger skier to push right through the boot to the point where you feel like you’re getting too far forward (as is the case with most boots in this class).

At 190 lbs (without any gear or outerwear) and 6’ tall and on 116mm-wide skis, I was able to ski the new Backland Carbon in most terrain and snow conditions that I encountered without any difficulty. The Backland Carbon provides substantial lateral stiffness and in low-density, consistent, boot-top pow, I could ski just about as fast as I would on any other boot. As the snow became more variable, deeper, or denser, I definitely had to pay more attention to my fore / aft balance and couldn’t lean into the front when things got weird as I can do on stiffer, heavier boots.

With skinnier skis and firmer, more consistent snow, the new Backland Carbon provides plenty of power for carving and skidding turns. It’s certainly not in the realm of the (much heavier) Dynafit Hoji Free or Scarpa Maestrale XT that I’ve also been skiing lately, but the Backland Carbon will handle these conditions without much difficulty.

I’ll soon do a Deep Dive with specific comparison to other boots in this category including the Scarpa Alien RS, which I consider the current category leader in both uphill and downhill performance. Stay tuned for that!

Paul Forward reviews the Atomic Backland Carbon for BLISTER
Paul Forward skiing in the Atomic Backland Carbon.

For now, suffice it to say that the Backland Carbon is a very respectable offering in the lightweight, 2-buckle category that can handle bigger skis and skiers and steep terrain. It is definitely not a “freeride” boot that allows you to ski as you would inbounds (again, as is the case with all the boots I’ve used that are this light). But for the vast majority of ski-touring scenarios, I think boots like the Backland Carbon are a great choice because they shave a ton of weight compared to stiffer boots and offer ridiculously comfortable uphill performance. They just require an awareness of your gear and dialing it back at times when things get more variable, fast, and challenging.

Durability

The usual concerns for boots in this category like thin rubber soles, fairly thin plastic, and more delicate hardware apply to this boot as much as they do any other light “2-buckle” touring boot. I’ve been skeptical of the BOA system since I first used it on the Scarpa F1 Evo, but so far I’ve skied many days on at least 3 different BOA boots with zero issues. I’m told that BOA is also fairly easy to replace if needed, but haven’t tested that myself.

I did have an issue with one of the buckles on the Atomic Backland Carbon on the last run of my day on one of the cold-weather touring days mentioned above. It looks like a small metal piece broke off the buckle assembly either while I was skinning back up or (more likely) while I was flipping into ski mode. I didn’t notice any clicks or pops but just looked down and noticed part of the buckle hanging loosely off the boot, disconnected from the rest of the buckle. I’m sure it’s an easy replacement and Atomic said it would definitely be covered under warranty, but worth noting.

Who’s It For?

The new Backland Carbon is a great choice as a dedicated ski-touring boot for those who prioritize comfort, low weight, and efficiency on the ascent but who still want just enough stiffness and downhill performance to be able to drive most skis in most conditions.

As I noted above, if you want to ski in the backcountry just like you do in the resort, you should check out heavier options (there are tons of great options in our 19/20 Winter Buyer’s Guide). But if you prioritize uphill performance and don’t mind dialing back your skiing when conditions are challenging, the Backland Carbon is another great addition to this class of lightweight boots.

Bottom Line

Personally, I still believe that the 1000-1200 gram, 2-buckle touring boot is likely the best choice for most skiers in most backcountry skiing scenarios. They save a ton of weight, are super comfortable on the ascent, and can ski the terrain and conditions that most of us encounter on purely human-powered ski days. The new Atomic Backland Carbon is a great example of this kind of boot, it compares very favorably to the other boots in its class, and if it fits your foot, it’s definitely worth a try.

Share this post:
2021-2022 Atomic Backland Carbon, BLISTER
2021-2022 Atomic Backland Carbon, BLISTER

43 comments on “2021-2022 Atomic Backland Carbon”

  1. I think that Scarpa F1 should be included in the overview of alternatives, too. And it would be interesting to compare these boots with Scarpa F1.

    • Good call — just added our average measured weight of that boot for reference, and Paul will definitely be comparing that boot in his full review.

  2. Luke is this some kind of experimental math you guys at Blister are pioneering?
    Blister’s Measured Weight (size 27.5):
    Shells, no Liners: 1110 & 1114 g
    Liners, no Footbeds: 228 & 230 g
    Shells + Liners = 1110 & 1114 g

    On topic:
    I did one day of frontside skiing in different piste conditions on this boot and I was amazed. Yes I was tired and my feet said no at the end of the day but I was using it in a way it was not designed for. It was a nice boot to ski on in good conditions and it was some work in bad conditions. But overall they didn’t suck and thats why I was amazed.
    I’ll be glad to read your opinion of actual backcountry usage and leave some room for the subtleties to you guys.

    • Ah, my bad. Some copy & pasting errors there — the total weights were correct, but they accidentally got pasted in as the shell weights. Updated with the correct weights. Glad to hear your initial impressions have been positive!

  3. When are you expecting to get some real world skiing and then review up on here?
    Really looking forward to hear how they ski compared to the original Backland Carbon.

    I forgot my tongues once skiing groomers at my hill and it was a very different boot and not in a good way.

    • Paul should be getting the boots on snow within 2 weeks, after which he’ll post a Flash Review with his initial impressions. Then for the full review, we’re probably aiming for a mid-January to mid-February publishing date.

  4. I bought previous version last season. I have normal feet feel most comfortable in 101 last, those were painful , too short cuff, my calf was squeezed , terrible fit for me! sold them after skiing once. Bought Scarpa alien 1.0

  5. I have these boots. Only got them out twice so far: once skinning up resort, and once on an early season, low angle tour up to Camp Muir on Mt. Rainier. Some quick thoughts:

    They are light as hell, and feel extremely mobile/agile-even when compared to other boots in this class. In my humble opinion, the ROM on these bad boys is comparable-maybe even better-than any other pair of boots I have tried. Haven’t gotten in the Aliens, but they feel more natural and nice to walk/skin than in the S/Lab X-Alp and TLT7s. I love them on the uphill. My other touring boots are the Atomic Hawx 130s, so maybe I am just happy to be out of those. But side by side testing the Backlands with the Dynafit and Salomon offerings, I am really happy with the uphill performance of these boots.

    Strong flex from the top of the boot. These aren’t race boots, not even close. But they do feel stiffer than any other boot I have tried in this class (maybe the TLT line is comparable). This was a big deciding factor for me, coming from burlier boots. I can drive through the top of the boot relatively powerfully-definitely moreso than, say, the S/Lab X-Alp. This is a strong boot for its class in my opinion.

    The Boa is awful. This is my biggest complaint about these boots so far. I cannot stay put in my boot when skiing, because it does not effectively tighten down very much. There is a lot of space between my forefoot and the boa, which isn’t dramatically reduced when tightened fully. The boot is relatively powerful, but it feels useless because of how much space my foot bounces around within my boot. When conditions are smooth, firm (corn), and steep; this isn’t a huge issue, as I can stay really forward. But in thick, heavy, chunky stuff-like the beloved “cascade Concrete” snow that I ski in the PNW (I know, that’s not what this boot is made for); I find myself sliding all over the place while shifting my center of balance. This has been my biggest challenge so far. Right now I am playing with a few different foam pads and fillers to reduce a little bit of space in the forefoot where the Boa sits. If I have any luck I will let folks know

    • Hey Alex,

      I agree 100%!

      Experienced the same problem with the boa here.

      Please let me know when you find a solution

      • @Dominik

        I have placed some medium-sized heel lifts in the boots in order to reduce the dead space where the Boa sits. The thought process was: by raising my foot higher into the boot, I could reduce some of the dead space that the Boa could not tighten. So far, the results have been decent! It’s no 4-buckle boot still, but tightening the Boa now feels a little more even and distributed. This is not a perfect solution, but it will probably be the only steps I take in the near future-at least until I am dissatisfied with the boot’s performance again. I am happy enough with this outcome. It feels a less like a floppy overboot, much more like a really proficient ski mountaineering boot.

        -it does help that my calf/ankle flexion is pretty limited, so skiing with a heel lift is already a natural position for me-

        Hope that helps!
        -AH

  6. Is there another boot in this weight class that has easily heat-modable shell similar to Atomic Memory Fit? I have some unusual feet and Atomic Memory Fit has been some of the only way for me to get a good fit. Thanks!

    • As far as we know, the Backland is the only boot in this class with a heat-moldable shell, though there’s a chance I’m forgetting something.

    • While other boots in this class don’t necessarily market themselves as having moldable shells, they do all feature grilamid plastic. I (and many boot fitters I’ve spoken with) have found that grilamid is quite easy to heat mold and it seems to take a mold very easily. They usually are made with thin plastic and there’s a bit of a learning curve when molding them so it’s probably best left to the shop if you haven’t done it a lot but overall my experience has been that all grilamid boots take heat molds very readily.

  7. I know this isn’t entirely related to the review of the Backland, but are you going to be publishing any thoughts on the Hoji Free, or the Maestrale XT anytime soon? I’m currently looking for a replacement for my S-Labs and both of those boots are high up on my list of possibilities…

    • We’re planning on publishing the Maestrale XT full review in the next couple of weeks, and the Hoji Free would be a bit after that (Paul just got that boot recently).

    • I’m working on the Hoji Free review now and have also spent a lot of time on the Maestrale XT as has Sam and possibly others. I am also going to do an updated deep dive comparing the various boots in this category like the Alien RS, X-Alp, TLT-7 (hopefully TLT8 at some point), previous Atomic Backland, F1, and Arcteryx Procline.

  8. //Some Questions / Things We’re Curious About// is the correct pronunciation “atomic” as in atomic bomb, or is it ATT – TOME – EEK ? Reason i ask is a Euro (French) female was telling me i was saying it incorrectly. The company is based in Austria. Regards.

      • Atomic is an English word. AFAIK the German is atomare and the French is atomique – pronounced as Bill suggests – so I assume the Austrian founders deliberately chose the English form.
        Blizzard was another Austrian ski company founded shortly after WW2 with an English brand. It may be that they feared a German brand would not sell well internationally.

  9. Trying them on, rearward flex is super stiff, lateral seems fine(a bit of play with my skinny calves), but forward flex seems very soft.
    I don’t plan on skiing as hard in the backcountry as I do inbounds, and general don’t drive my tips very much. On the other hand, I don’t have great technique, and with funky snow, would a taller guy like me (6’5”, 178lbs) on 185cm 105mm ski’s, get in trouble? Meaning, would I get thrown to far forward to easily?

    • Hey tjaard, What setup are you coming from? A true 130 flex inbounds boot? I would say that you will likely get knocked around if your technique isn’t 100%…in thick or heavy snow, I’m not really able to power through the hooky/grabby stuff. I can drive my skis well enough on firm snow, but I feel that most boots in this category don’t really provide the power and precision to shred through nasty snow-for my personal use at least. I still roll with them for bigger days because that walk is so fluid and sweet…but maybe something with a little more compromise like the Hoji or Maestrale XT would be a better balance if you’re already overpowering the forward flex. Just my 2 cents after putting in half a season with these boots. I’ve found that the firmer the snow is, the more manageable skiing these boots is for me. It’s a “sneaky high-volume” boot for me.

      • I ski a current model Cochise 120, so not the stiffest 120, but a true inbounds boot. I also used to have the previous generation Maestrale RS, which was plenty stiff for me too.

        I never ‘shred’ or ‘power through’ in the backcountry. Or, if I suddenly would get the urge, I could use my Cochise, theY walk ok with a tour liner in there, I have done it several times.

        So mostly worrying about hitting a patch of something and getting knocked forward.

  10. I have a new pair of 28-28.5 and there is a little play/rattle in the walk/Ski latch. Seems like both the lever socket to bar connection and the upper pins that the lever pivots on.
    Together there’s slight play but mostly it rattles or rapid taps when I ski.
    It’s specially noticeable in quite rec room on carpet walkin on toes. Thanks

  11. Hey great review, the ski shop pointed me to the older version of this boot and claimed it would be compatible with the shift binding, Mine looks to be the 2017 version. Would this be possible?

    • Nope. That toe isn’t compatible with the SHIFT binding. The old and new Backland line can only ride on pin toes. But honestly it would be hard to imagine getting a lot of value skiing a heavy setup with these boots.

      Sorry about that, good luck!

    • I’ve done it without modifying the boot. My wife does this currently. Would recommend adding the metal beast heel adapter though. But I agree that these boots (and the 2017 version) are better suited for a tech binding. Currently using them with the Tecton and a beast heel piece. This is my second pair of the old version of this boot.

  12. One year out review-because nobody asked for it.

    These boots are a blast. I pair them with Fischer Hannibal 96s and the Salomon MTN binding. This was supposed to be my UL setup but it made uphilling so damn pleasant this became my daily driver quickly. I have changed my skiing technique and process as I have grown to appreciate these boots more…and I think that’s a good thing? Or maybe I am just getting old and scared to huck cliffs. The style of skiing which lightweight boots + skis requires- as well as the terrain they are best suited for-are best managed with balance and an even foot; rather than a progressive foot stance which allows the skier to drive into the skis aggressively. If that’s your style of skiing, something will give.

    Fit: I have a low volume foot with a low instep. On the uphill, I prefer to skin with the BOA open, although I have had concerns about the durability of the BOA while booting. No actual issues yet, but fear. Same with the F1 and the Alien, however-so pick your poison. When strapped into ski mode, however, I find that the BOA is not terribly useful still. I had grumbled for the first few months about how little the BOA does for those with smaller feet. I still think it does not offer fantastic touch/fit. I have also found that the upper buckle and power strap provide a plenty-tight fit for my low-to-mid volume calf. No legitimate complaints. I was riding with with a heel riser under my superfeet insole in each boot for a few months, but have removed those and been ultimately more pleased without them.

    Uphill: still amazing, still speedy. much like Paul says, this boot kicks ass because it is exceptional on the uphill and somewhat tolerable on the downhill. I would be wary with how your automatic crampons fit with these boots-mine do align but the toe is so diminutive (a la Dynafit speed nose) that many crampons will not fit. I flew back east to ski/climb in Huntington and Tuckerman Ravines, and the automatic crampons I rented would not fit.

    Downhill: I have grown to love the fit and stiffness of the boot. It isn’t the perfect fit for me, having a low volume + low instep, but that amount of tightness I would want on my forefoot translates to far more aggressive skiing than I am doing in these boots. The calf buckle and power strap really absorb most of my effort. As Paul mentions in his review, you can certainly overpower this boot if you try- there is a ramp you can push past. But I can easily reach 30 MPH and be happy on these boots/skis. Any faster and my lightweight skis wouldn’t hold up anyways. I’m no racer or freerider, and you shouldn’t be trying to do that type of stuff with this touring boot. With a greater appreciation for balance, core strength, and ski form than I used to use, I am really enjoying the stiffness and ride on these boots. Just keep in mind that it all comes from the top buckle.

    Durability: Some new/interesting wrinkles here. I have probably logged 35 days on these boots, and not been particularly kind to them. Lots of scrambling, miles of choss jogging, bootpacking, and dirty paths. Carbon, lightweight boots will never hold up to the kind of thrashing a heavier, thicker one would-which is unfortunate, because these are the ones likely facing more rock and ice climbing, etc. …Anyways, only two real things worth noting here. The rubber Skywalk sole was really chopped up after my last ski this summer. Sharp rocks and a little carelessness on a downclimb meant that about a quarter of the traction lugs were hacked up in some capacity, and the rubber was peeling from the sole in other places. Definitely what will likely deteriorate first for most folks. Shoe Goo bought me some more time, but it is still a ticking clock. The second issue is less aggressive, but certainly more concerning. on the outside of the big toe of each ski boot (where the most force is transferred from skier to boot to binding to ski), there is a long but thin crack which has developed. The 1.5″-2″ cracks align directly the end of the hidden wires of the BOA mechanism. I wonder if the damage has anything to do with the compression caused by the BOA immediately next to an area with no pressure/compression; all superimposed on some thin, brittle carbon? Now I am just speculating and rumor-mongering. I have chatted with a handful of other skiers in this new version of the boot, and none had experienced this. Also chatting with Atomic to hear if they have seen this issue before. Nothing has led me to believe it is systemic or pervasive in the Backland Carbon boot line yet. I have not experienced durability issues or failures with the walk mode, lever, buckle, or BOA yet. The Power Strap is a little tattered but that is to be expected. I have done a number on the D Ring for leash attachments but it is surviving-all boilerplate stuff.

    Overall I am really happy with this boot. If you are willing to sacrifice 20% of your downhill performance, you will increase your uphill by 45%-50% (totally made up numbers).

    Ok, now back to work! Enjoy La Nina if you are on the West Coast like me.

  13. Have anyone heat mold shell of the backland carbon 2020/21? I was told here in Austria by a good fitter that they dont heat mold outer shell, only liner, because carbon could break and then they have to pay for another one…But I have problems on inner side of ankles, bigger maleols…

    Thanks!!

    • I`ve got a pair of Hawx Ultra s 130 (alpnie version without pins) and Backland has a pretty similar fit. Feels a bit more roomier but still snug enough. I wish Atomic will makes Ultra xtd in bigger MP one day.

  14. Had about 70 days in the 19/20 Carbon Backland. Warrantied them as the BOA broke on one of the boots and the gaiters on both developed large holes where the cuff rubs. Atomic does not have an easy way to fix the BOA so they just replaced my boots with the 21/22 version. The BOA broke about 40 days into their use but a Voile strap over the arch fixed the problem and actually held my foot much better.

    I also had 4 years and about 250 days on the original black/orange Backland Carbons. They also had lots of holes on the gaiter but I was able to eventually get some replacement gaiters. The originals tour way better than the new boots but skiing is not nearly as good.

Leave a Comment